Showing 1–10 of 17 results

HD Kayak Stabilizer Floats Complete Package

$425.00

Spring Creek Manufacturing’s float stabilizer packages are the safety and comfort you are looking for while on the water. Made from durable, lightweight Polyethylene plastic, the floats are designed to keep your kayak stable and upright. Complete Package comes with Universal Receiver (UR), Clamps, Hydrodynamic Floats, Float Tubes, and Float Arms that telescope out for desired width. For additional information regarding UR sizes and specifications, Please visit the UR product page on the web site.

  • Hydrodynamic Design for minimal drag through the water and excellent stability.
  • Easily adjustable with locking cam lever arms.
  • Color options: Grey, Red and Yellow.
  • Telescope distance 20″ each arm.

Replacement Floats

$110.00

One standard replacement HD float.

Kayak Adapter Kit

$70.00

Use these Spring Creek Kayak Adapters on your kayak to convert your Spring Creek Canoe Stabilizers into kayak stabilizers.

Attached right to your Spring Creek UR!

These adapters have two leveling legs that are pinned into the brackets.  Just one pull of the pins and your adapters are off your boat. Just the low profile brackets will remain on your boat.

Brackets and bolts incluced.  Buy extra brackets for another kayak, or for multiple stabilizer locations. Comes with bolts.

Suction Cup Rack

$225.00$325.00
Rated 5.00 out of 5

Spring Creek Manufacturing’s Suction Cup Rack. Price is for ONE RACK.

These universal roof racks do not require any special clips, bolts, or clamps for your vehicle. Included are our through cab straps and handle straps for your desired strapping needs. The straps thread through your open doors.

The suction cup mounts protect your roof from scratches or dents. The tops of the racks are padded to protect whatever you may be hauling. The racks are made from anodized aluminum and stainless steel, so they will not rust. Wide enough for canoes, kayaks, sailboats, ladders, lumber etc.

Add our telescoping loading bars for easier loading and wider carrying ability. Up to 20″ of added width on each side with loading bars fully extended. Loading bars extend and adjust to various widths to fit many requirements.

Suction Cup Racks are rated for 300 lbs, although your car’s roof may have a lower load limit.

Racks come in two sizes, 53″ for cars and thinner SUVs and 65″ for Trucks and bigger vehicles.

The top rack bar is 2-3/16″ wide and 1- 1/2″ high.

Through Straps and Handle Straps included.

Please specify 53″ for smaller vehicles or 65″ for full sized vehicles.

*Rack Pictured has loading bars*

Double Hitch Rack

$250.00

An exclusive Spring Creek design.

All aluminum, this handy rack telescopes vertically up to the largest pickup height.

Approximately 68″. 36″ long horizontal bar is padded and comes with extension bars that will extend out approximately 20″.

 

DIY Suction Cup Rack Kit

$75.00

This kit, manufactured by Spring Creek Outfitters, provides all the parts you’ll need to convert a standard 2×4 into a rock-solid rack at an inexpensive price. You get everything to make ONE rack, including: two suction triangles, straps to attach to car, two eye pads and hardware.

Directions:

To construct your rack, you first have to decide what length 2×4 you will need.

If you are going to be hauling two canoes, we would recommend using a 78” 2×4. If you are hauling only one canoe, use a 2×4 that is slightly larger than width of your vehicle.

Bolt the suction cup frames to the 2×4’s so the cups are to the outside edges of your roof, by drilling a 3/8” hole (or a little bigger, if you want to remove it later – to allow for wood swelling.)

Set the rack on the roof to see where to place the buckles and buckle holders to make sure they are pulling straight down and drill two other slightly over 3/8” holes and bolt on the buckle brackets. Then, place black eyepads on the ends of the 2×4’s where you wish, and bolt them on.

Black straps must be placed through the cab of vehicle by opening doors and then snugging down securely.

This includes hardware to make ONE rack.

 

Load Stops

$50.00

These sturdy little stops clamp on easily to our Spring Creek Rack. Use them to hold your loads from shifting. Can be used on, Spring Creek’s Hitch Rack, Suction Cup Rack, Yakima, Barrecrafters or Thule Racks. Each order gets you 2 Load Stops. Approximately

3″ high and 4″ wide. Set of 2.

Top Ties

$13.50

Having trouble finding a place to tie down loads to the top of your vehicle? Well we have just what you are looking for! Spring Creek Manufacturing’s Top Ties take little time to install, and are extremely easy to use. Simply open the hood of your vehicle, unscrew the fender bolt, slide on the grommet end of the Top Tie and reattach. It’s that easy! No more crawling under your vehicle to look for a tie down location.

  • Tough 1″ Nylon loop
  • Solid Brass Grommet
  • Top Ties sold in Pairs

Quick Hood/Trunk Loops

$25.00

Spring Creek Manufacturing’s Quick Hood/Trunk Loops create a quick and removable anchor point for all your vehicle tie down needs. Simply set the rubber wedge inside the trunk or under the hood, while leaving the loop end outside. Shut the trunk or hood of your vehicle to lock the loop in place with pressure. The exposed loop adds a very easy access point for tying down.

  • Sold in Pairs

Canoe/Kayak Portage Cart

$250.00$275.00

The Spring Creek Manufacturing Portage Cart is made from durable lightweight aluminum and stainless steel with vinyl covered supports.

Portage Carts come with your choice of 12″ or 16″ Inflatable Wheels. It is recommended that the 12″ Wheels be used on smooth paths. For rougher terrain we recommend 16″ Wheels.

The Spring Creek Portage Cart is extremely well made for years of easy portaging. The Portage Cart quickly assembles and disassembles for compact storage. Wheels fold in like an airplane’s. The No-Axle design gives you high ground clearance. The telescoping handle acts as a kickstand support. The Bunks adjust to any distance spacing along the 30″ wide top bar.

It is designed to be towed by a person while holding onto the end of your canoe or kayak.

The wheels should ideally be placed a third of the way from the back of your canoe or kayak to balance your load and for easier rolling.

The cart comes with 7′ long tie-down straps.

Can carry 1 canoe or kayak.

12″ cart weighs only 16 lbs and 16″ cart weighs 25 lbs.

Load Limit 250 lbs.